Hβ/Al-SBA-15介微孔复合分子筛负载Ni-W催化剂对萘加氢裂化制BTX的催化性能

采用后合成法制备Hβ/Al-SBA-15复合分子筛,利用XRD、N_2吸附、Py-IR、NH_3-TPD、SEM和TEM等手段进行表征。用浸渍法将Ni-W活性组分担载在Hβ/Al-SBA-15载体上,制备Ni-W/Hβ/Al-SBA-15催化剂,以萘为模型化合物,考察该催化剂的加氢裂化性能。结果表明,所合成的Hβ/Al-SBA-15复合分子筛既有介孔结构又有微孔结构,并同时具有B酸和L酸中心,酸性强于SBA-15。具有适度酸性位和介微孔结构的Ni-W/Hβ/Al-SBA-15催化剂,对萘加氢裂化具有较高的萘转化率和BTX选择性,分别为96%和61.1%。     

Ni-Mg复合催化剂催化裂解CH_4制氢动力学研究

基于定温热重实验,建立了甲烷催化裂解反应动力学模型和催化剂表面积炭失活动力学模型。其中,甲烷催化裂解动力学模型将初始产氢速率视为催化剂未积炭条件下的动力学基础数据;催化剂表面积炭失活动力学则基于甲烷催化裂解速率的降低。实验使用Ni-Mg复合催化剂,分别在535、585、635℃,甲烷分压10~4、2×10~4、3×10~4Pa条件下展开甲烷催化裂解动力学特性研究。结果表明,甲烷催化裂解的反应级数为0.5,活化能为82 k J/mol;Ni-Mg复合催化剂反应失活级数为0.5,催化剂失活活化能为118 k J/mol。实验条件下均制得了多壁碳纳米管。     

山西典型高铝煤灰熔融及黏温特性改性实验研究

以山西典型高铝煤为研究对象,研究了工业助熔剂石灰石、黏土以及两者的复合助熔剂对其灰熔融特性及黏温特性的影响。结果表明,随着助熔剂含量的增加,煤灰熔融流动温度下降;石灰石的助熔效果优于黏土,复合助熔剂效果优于单一助熔剂。添加石灰石使灰渣临界黏度温度tcv显著降低,添加黏土使其渣型向玻璃渣转变,复合助熔剂较单一助熔剂存在显著协同作用,即能同时实现tcv的降低和渣型的有利转变。对山西典型高铝煤两渡煤,在复合助熔剂添加量为4%(2%石灰石+2%黏土)时,不仅其渣型向玻璃渣转变,且tcv较单独添加石灰石(2%)降低133℃,较单独添加黏土(6%)降低222℃。矿物质分析结果证实了助熔剂的助熔原理。添加复合助熔剂改性的山西高铝煤可达到工业气流床气化对煤种的要求。     

亚微米级Cu0/Fe3O4复合物多相催化过一硫酸盐降解有机污染物

过一硫酸盐催化活化技术因其可产生强氧化性活性氧化物种,可快速氧化降解并矿化有机污染物的优异性能而备受关注.本文成功制备了亚微米级Cu0/Fe3O4复合物,发现其能多相催化过一硫酸盐产生单线态氧降解有机污染物.首先,以CuCl2·2H2O,FeCl2·4H2O和FeCl3·6H2O为铜源和铁源,水合肼为还原剂,采用水热法在180oC反应24 h制备了亚微米级磁性Cu0/Fe3O4复合物.表征结果显示,所制材料为Cu0和Fe3O4的复合物,颗粒大小约为220 nm;单一相Cu0和Fe3O4晶体粒径分别为33.8和106.2 nm,而Cu0/Fe3O4复合物中Cu0和Fe3O4晶体粒径分别减为20.8和31.9 nm.这表明Cu0和Fe3O4复合降低了Cu0和Fe3O4晶体粒径,有利于Cu0和Fe3O4的分散.BET测试结果表明,Cu0/Fe3O4复合物比表面积为4.6 m2/g,与Cu0颗粒的(4.2 m2/g)相当,但远小于Fe3O4的(15.6 m2/g).制备的Cu0/Fe3O4复合物可有效催化过一硫酸盐产生单线态氧降解罗丹明B、亚甲基蓝、金橙II、苯酚和对氯酚.当Cu0/Fe3O4复合物的用量为0.1 g/L,过一硫酸盐浓度为0.5 mmol/L和初始pH为7时,Cu0/Fe3O4复合物可在30 min内完全降解20μmol/L的罗丹明B、亚甲基蓝、金橙II以及0.1 mmol/L的苯酚和对氯酚.对比试验显示,在相同条件下,Cu0和Fe3O4颗粒分别可以降解28%和20%的罗丹明B.这表明Cu0/Fe3O4复合物中的Cu0和Fe3O4晶体在催化过一硫酸盐降解污染物的反应中具有协同作用,这主要来源于Cu0/Fe3O4复合物中Cu0和Fe3O4的晶体粒径变小和更好的分散.采用分光光度法测定了降解反应液中铜和铁离子的溶出量.当Cu0/Fe3O4复合物的用量为0.1 g/L,过一硫酸盐浓度为0.5 mmol/L和初始pH为7时,反应60 min后,降解液中铜和铁离子的浓度分别为0.22和0.1 mg/L,仅占复合物中总铜和总铁量的1.1%和0.2%,表明Cu0/Fe3O4复合物具有较强的化学稳定性.所制Cu0/Fe3O4复合物具有超顺磁性,借助磁场实现快速分离回收,可循环利用五次,表明其优越的催化稳定性.通过加入乙醇和叠氮化钠,考察了Cu0/Fe3O4复合物催化活化过一硫酸盐体系中的活性氧化物种.发现100 mmol/L乙醇的加入对污染物的降解无明显影响,而加入同等量的叠氮化钠可完全抑制污染物的降解,表明Cu0/Fe3O4复合物催化活化过一硫酸盐产生的主要活性氧物种为单线态氧.采用电子顺磁共振谱进一步证实了单线态氧的生成.基于以上研究,Cu0/Fe3O4复合物催化活化过一硫酸盐的机理为Cu0/Fe3O4作为一个电子媒介加速过一硫酸盐和污染物之间的电子转移,从而导致污染物被快速降解.该反应机理不同于常见的金属催化过一硫酸盐产生硫酸根和羟自由基的反应机理.我们推测,电导性优良的Cu0在此催化反应中起着关键性作用.本催化方法可作为一种绿色的氧化技术用于环境污染物的氧化降解处理.     

协效剂对膨胀阻燃聚丙烯基木塑复合材料的阻燃增效研究

赋予木塑复合材料(WPC)的阻燃性能成为近年来该领域国内外的研究热点之一。本文通过两轮正交试验,研究8种常见的协效剂对膨胀型阻燃剂(IFRs,m(聚磷酸铵,APP)∶m(季戊四醇,PER)=2∶1)的阻燃增效作用,筛选出具有显著协效作用的协效剂组MgO/EG(可膨胀石墨)/SiO_2,其组成为m(MgO)∶m(EG)∶m(SiO_2)=1∶5∶5,其与IFRs的最佳配比为m(IFRs)∶m(MgO/EG/SiO_2)=1∶0.18,得到性能良好的阻燃型聚丙烯基木塑复合材料。通过热重分析(TGA)和锥形量热分析(CONE)评价IFRs及协效剂组对聚丙烯(PP)基木塑复合材料(WPC)热稳定性能和阻燃性能的影响。结果表明,IFRs及MgO/EG/SiO_2的加入可以有效提高WPC的热稳定性,WPC/IFRs/MgO/EG/SiO_2600℃的残炭率达到22.42%。WPC/IFRs的热释放速率峰(PHRR)、总热释放量(THR)和总烟释放量(TSP)相比于WPC分别降低了21.9%、8.7%和22%。MgO/EG/SiO_2的加入可以进一步提高IFRs的阻燃效率,WPC/IFRs/MgO/EG/SiO_2的PHRR和THR相比于WPC分别降低了33.0%和13.8%。     

静电喷雾结合热压处理制备荷负电PVA-SA/PAN纳米纤维基复合滤膜及其纳滤性能研究

以静电纺丝聚丙烯腈(PAN)纳米纤维作为多孔支撑层,以亲水材料聚乙烯醇(PVA)和海藻酸钠(SA)为亲水表层材料,通过静电喷雾技术将亲水表层材料沉积在纳米纤维多孔基膜表面,然后将表层PVA-SA纳米串珠层通过水蒸气加湿辅助热压成膜处理在PAN基膜上软化压延形成完整的致密薄膜,最后经过戊二醛交联制备PVA-SA/PAN纳米纤维基复合滤膜.通过对加湿时间、热压温度、热压时间以及PVA-SA静电喷雾时间等成膜工艺条件和交联条件进行优化制备出结构完整的PVA-SA/PAN纳米纤维基复合滤膜.所制备的复合滤膜荷负电,它对阴离子染料具有较好的过滤效果:在0.6 MPa的操作压力下对100 mg/kg的固绿染料的渗透通量为57.1 L/(m~2h),截留率为96.8%.     

具有高灵敏性且稳定可重复的正温度系数效应的PVDF/CF导电复合材料

以碳纤维(CF)为填料,聚偏氟乙烯(PVDF)为基体,通过熔融共混法制备PVDF/CF导电复合材料.所得复合材料具有显著的正温度系数(PTC)效应,温度上升到聚合物熔点附近时,电阻率对温度变化敏感.在转折温度区间(155.5~171.0oC,(35)(28)15.5oC)内,其体积电阻率的增加速率约为1.3×105?cm K-1.在不同CF含量下,复合材料表现出不同的PTC行为.随着CF含量的增加,其峰值电阻略有下降.高导电粒子含量下,无负温度系数(NTC)效应.在冷却循环过程,导电网络的重构性良好.复合材料即使经过多次热循环,依然表现出良好的PTC特性重现性.     

Electrochemical Determination of Uric Acid Using a Multiwalled Carbon Nanotube Platinum–Nickel Alloy Glassy Carbon Electrode

Platinum–nickel nanoparticles were synthesized by a reduction procedure. The Pt–Ni/C composite was characterized by X-ray diffraction, infrared spectroscopy, transmission electron microscopy, and electrochemical analysis. The measurements show that the Pt–Ni/multiwalled carbon nanotubes provided higher electrocatalytic activity for the oxidation of uric acid than Pt–Ni/carbon black. The sensor prepared from the characterized material provided a long linear dynamic range from 0.1 to 240.4?µM with a detection limit of 0.03?µM and a sensitivity of 41.21?µA?mM^?1?cm^?2. The reported modified electrode also provided excellent selectivity, good stability, and satisfactory reproducibility for the determination of uric acid.     

J-integral evaluation of nanoclay-modified HDPE/PA6 microfibrillar composites

Microfibrillar composites (MFC) are polymer-polymer composites with many advantages, including good dispersion and bonding of in-situ generated fibrils. Recently, it has been shown that their performance can be enhanced by suitable addition of organophilized montmorillonite (oMMT) provided the numerous oMMT-induced effects are harmonized. This work deals with evaluation of resistance against unstable crack propagation (J-integral) in combination with Charpy and tensile impact strength methods, and SEM observation of fibrils shape and size and fracture surfaces. The results indicate that addition of PA6 inclusions and oMMT to relatively ductile HDPE reduces toughness evaluated using Charpy and J-integral. The fact that tensile impact strength is not reduced by oMMT indicates the importance of the impact testing mode for MFC. Of importance is the fact that formation of PA6 fibres reinforced with oMMT practically does not reduce toughness. Hence, the drawn oMMT-modified system with significantly higher stiffness and practically unchanged fracture resistance can be obtained. Combination of the complex effect of oMMT and in-situ fibrils reinforcement present a tool to attain polymer systems with enhanced well-balanced properties.     

Effect of Polyethylene glycol methyl ether blend Humic acid on poly (vinylidene fluoride-co-hexafluropropylene) PVDF-HFP membranes: pH responsiveness and antifouling behavior with optimization approach

Flat sheet asymmetric membranes were fabricated with homogeneous solution of poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) using N-methyl-2-pyrrolidone (NMP) as solvent via phase inversion method. PEGME (Poly ethylene glycol methyl ether) (M_n 5000) blend Humic Acid (HA), of different mole ratio was used as additive. Characterization of the membranes was done by Field emission scanning electron microscope (FESEM), Fourier Transform Infrared (FTIR) spectroscopy, Atomic force microscopy (AFM) and Differential scanning calorimetry (DSC) studies. Liquid-liquid displacement porosimetry (LLDP) study evaluated the morphological parameters, average pore size and pore size distribution. Bovine serum albumin (BSA) (M_W - 68,000 Da) was used to study the antifouling effect and pore blocking mechanism of the membranes. The pure water flux (PWF), solute rejection and flux recovery ratio drastically increases for the PEGME blended HA membranes whereas the water contact angle decreases significantly. The pH responsiveness character of the prepared membranes altered the hydraulic permeability and rejection % at different pH. Finally, optimization of the variables contributing towards the PWF and BSA rejection of the desired membrane was performed using Design expert software 9.0 TRIAL through ANOVA (analysis of variance) using the combination of response surface methodology (RSM) and central composite design (CCD).